Combine Harvester Threshing & Cleaning System: Reduce Grain Loss, Fix Plugging

Once the header has cut the crop, two systems decide how much grain actually reaches the tank and how clean it is: the threshing unit and the cleaning shoe. Most of the grain loss, cracked grain and dirty samples operators blame on “an old machine” are not wear at all — they are a mismatch between cylinder speed, concave clearance, fan blast and sieve opening. This guide walks the crop path from header to tank, gives a symptom-by-symptom fix table, and lists the few parts that genuinely need replacing when adjustment no longer works.

From the header to the grain tank: the threshing and cleaning path

After the reel and cutter bar gather the plants (the feed end is covered in the combine header system guide), the feeder conveyor moves a continuous, even mat into the machine. The crop then passes between the rotating threshing cylinder — fitted with rasp bars — and the stationary curved concave grate below it. The rubbing action frees the grain, which falls through the grate openings onto the cleaning shoe. A fan blows the light chaff away while the heavier kernels fall through the chaffer and lower sieve; the clean grain is carried by the grain auger to the tank, while unthreshed tailings are returned for a second pass.

Every stage shares one rule: the machine wants a steady, even feed. Uneven or excessive feeding is behind more threshing and cleaning complaints than any broken part, which is why ground speed is itself a threshing setting.

The threshing stage: balance cylinder speed against concave clearance

Two variables do almost all the work here. Cylinder (rotor) speed controls how hard the crop is struck, and concave clearance — the gap between the bars and the grate, set wider at the front and narrower at the rear — controls how long and how hard it is rubbed.

  • Clearance too wide or speed too low: heads pass through unthreshed and pile up in the tailings. You will see whole heads in the tank and a heavy return load.
  • Clearance too tight or speed too high: kernels are cracked and the straw is shattered into small pieces that blind the sieves. A tight concave typically leaves split kernels and crushed pod or cob pieces in the sample.

Make one small change at a time and inspect the tank after each pass. On many Asian-track combines the cylinder also carries bolt-on threshing tooth bars; bent or missing teeth leave strips of crop unthreshed even when the clearance is correct.

The cleaning shoe: balance the fan, chaffer and lower sieve

Beneath the concave, the material lands on the shaking shoe. The upper chaffer holds the straw while grain falls through, the lower sieve does the final cleaning, and the cleaning fan lifts chaff out of the machine. These three must be balanced together rather than tuned one at a time:

  • Fan blast too high: kernels float or bounce over the rear of the chaffer. If you can pick up sound grain on the ground roughly 20–30 cm behind the machine, the fan is too strong or the chaffer is too open.
  • Fan blast too low or the shoe overloaded: grain is trapped in bunches of chaff at the end of the chaffer and dirty grain reaches the tank. Open the chaffer and raise the fan slightly.
  • Lower sieve too open: chaff slips into the clean grain. Too closed, and clean grain is carried back as tailings, overloading the return.

Damp, weedy or high-test-weight crop needs more air and a slightly slower feed; dry, brittle straw needs less fan to avoid blowing grain out. Always set the machine for the worst part of the field.

Symptom-by-symptom troubleshooting

SymptomLikely causeFirst adjustment
Unthreshed heads in tank / heavy tailingsConcave too wide, speed too lowNarrow clearance, raise cylinder speed
Cracked or crushed grainConcave too tight, speed too highOpen clearance, lower speed
Sound grain blown out behindFan too high / chaffer too openLower fan, close chaffer slightly
Chaff and dirt in the tankFan too low / lower sieve too openRaise fan, close lower sieve
Cylinder plugging / sluggingOverfeed, wet crop, loose drive beltSlow ground speed, check belt tension

When adjustment no longer works: the parts that actually cause loss

If the correct settings cannot be reached — the clearance will not close far enough, or loss returns immediately — the hardware is worn and no adjustment will compensate. Inspect these before the season:

  • Worn rasp bars, threshing teeth and concave grids that round off and reduce the rubbing action.
  • Bent or broken chaffer and sieve louvers that let chaff through or hold grain back.
  • Worn fan blades and slip pulleys that deliver less air than the lever indicates.
  • Worn flighting on the unloading auger, which slows emptying and encourages operators to overfill.

Pre-season and in-field checklist

  • Spin the cylinder and check every rasp bar and tooth for wear, cracks and secure bolts.
  • Inspect concave wires and both sieves for bent louvers; confirm the clearance moves evenly front to rear.
  • Run the fan at full speed and listen for slipping; check drive belts for cracks and glazing.
  • Start with the recommended settings, then change one variable per pass and sample the tank.
  • Watch the mat entering the feeder — keep it even and slow down in heavy, laid or uphill crop.

Order the wear parts from one consolidated list

Threshing and cleaning parts are easiest to manage as a single list: collect the part numbers from the concave, bars, sieves, fan and augers, send it once, and get one quote back instead of chasing several suppliers. High, mid and budget grades are available for the fast-wearing items, common parts are kept in stock for quick dispatch, and mixed part numbers can ship together so the machine is ready before the next season. Send the model plate and part numbers through the quote form or WhatsApp and the fit will be confirmed before anything ships.

Leave a Comment

Your email address will not be published. Required fields are marked *