Combine Harvester Rubber Track Guide: Size Code, Measurement & When to Replace

Rubber tracks are the single most important wear item on a track-type rice combine. A matched pair carries the full weight of the machine through flooded paddy, spreads the load over a wide contact area so the harvester does not sink, and protects the road surface when the machine moves between fields. Because a track is expensive and a failure stops the machine mid-season, buyers benefit from knowing how to read the size code, how to measure an old track, and how to get the longest life from a new set.

This guide explains the three-number size code used on Kubota and other combine harvester tracks, the correct way to measure width, pitch and link count, the warning signs that mean a track should be replaced, and the undercarriage parts — sprockets, idlers, rollers and seals — that determine how long a track lasts.

How to read this guide. Prepared by the Agri Part Supply spare-parts team. The size codes and measurement method below follow the standard Width × Pitch × Links convention used across the industry. Always confirm the exact code stamped on your own track and the fit chart for your machine before ordering; the stamped number, not a generic model list, is the authoritative reference.

1. Why combine harvesters run on rubber tracks

A tracked combine places a large, flexible belt over a drive sprocket, front and rear idlers and a row of track rollers. The rubber belt is reinforced with steel cords and embedded metal drive lugs. Compared with wheels, this layout gives a far lower ground contact pressure: Kubota lists a ground pressure near 20.7 kPa for its DC-70G/DC-105X class, which is what lets a heavy harvester work in soft, deep paddy without sinking and travel without damaging the surface underneath.

The same wide contact area also gives traction in mud and stability on slopes. The trade-off is that the track is a consumable: the tread wears, the rubber ages and cracks, and the steel carcass can be damaged by sharp stones, bad driving habits or a worn undercarriage.

2. How to read the rubber track size code

Harvester rubber tracks are written as three numbers in millimetres, always in the same order:

Width × Pitch × Number of Links

  • Width — the outer width of the belt in millimetres. Wider belts lower ground pressure; harvester tracks commonly run from about 400 mm up to 575 mm and beyond.
  • Pitch — the centre-to-centre distance between two adjacent inner drive lugs (the metal cores that mesh with the sprocket), measured in millimetres. Common harvester pitches are 90, 93 and similar values.
  • Links — the total number of inner drive lugs counted around the whole loop. Link count controls the loop length and therefore whether the track fits the tensioning range.

Some codes add a letter, such as 450×90×56N. The letter marks a guide or tread-pattern variant rather than a change in the three core dimensions; match it against the old track or confirm it with the supplier before ordering.

Size code (Width × Pitch × Links)Typical machine / applicationNotes
500 × 90 × 53 / 54 / 56Kubota DC-70 class (aftermarket sources vary)500 mm wide, 90 mm pitch; link count differs by sub-version — read the stamped code
575 × 93 × 58Kubota DC-105 class575 mm wide, 93 mm pitch, 58 drive lugs
450 × 90 × 56Kubota AR-70 class450 mm wide, 90 mm pitch, 56 links

Because the DC-70 link count is quoted differently across aftermarket sources, never assume a number from a machine list. Read the size stamped on the inside of the track and count the links yourself.

3. How to measure an old track correctly

Park the machine on level ground, switch it off and clean the belt so the inner lugs are visible. Measure in millimetres and take more than one reading, because worn or stretched rubber can vary around the loop.

  • Width: measure across the outermost edges of the belt at two or three points and average; worn, rounded edges can make a single reading misleading.
  • Pitch: on the inside, measure from the centre of one drive lug to the centre of the next — not the gap between them. Repeat at three to five spots and average. Measuring the open gap instead of centre-to-centre gives a value that is too small.
  • Guide type: note whether the guides run between the rollers or outside them, and photograph the inner profile and sprocket tooth shape. A wrong guide type causes the track to run off-centre or derail.
  • Link count: pick a clear starting lug and count every inner lug around the full loop, then count again in the opposite direction to confirm the total.

4. When a rubber track should be replaced

Fine surface cracks are normal as rubber ages, but the following signs mean the carcass is failing and the track should be replaced before it breaks in the field:

  • Exposed steel cords or fabric — if the steel cables show through the rubber, fit a new track immediately; a blown track can damage the rollers and idlers around it.
  • Deep cuts or cracks — cuts that go well into the body, or deep cracks between lugs and across the belt, indicate structural failure rather than surface aging.
  • Missing or damaged drive lugs — lugs that are torn off stop the sprocket driving smoothly and cause ratcheting and lost traction.
  • Worn tread — when the ground bars are worn low and traction falls off, the track is near the end of its life; use a straight edge across the tread blocks to track wear.
  • Stretched beyond adjustment — if the tensioner reaches the end of its travel and the belt still cannot be tightened, or the track keeps ratcheting, the loop has grown too long.
  • Uneven wear from misalignment — one-sided scuffing points to an idler or roller problem that should be corrected, or the new track will wear the same way.

5. How to extend track life — and the undercarriage parts that matter

Most early track failures are not manufacturing defects; they come from over-tensioning, sharp turning and worn metal components. A few habits make a large difference to service life.

Driving and tension habits

  • Keep the correct tension. Too tight raises carcass stress and wears the belt; too loose causes ratcheting and derailment. Follow the OEM sag specification and re-check after the first hours on a new track, when a fresh belt settles.
  • Avoid pivot and sharp turns on hard ground. Skid-steer turns scrub the tread and twist the carcass; make wider, gentler turns where possible.
  • Clean out mud and stones. Packed mud and trapped rock between the lugs distort the pitch and grind the belt; wash the inside of the track after work.
  • Keep oil and chemicals off the rubber and store idle machines out of prolonged direct sunlight.

Inspect the undercarriage as a set

A new track fitted over worn metal will still fail early. When ordering a belt, inspect the parts that guide and drive it:

Common questions

What do the three numbers on a rubber track mean?

They are Width × Pitch × Links, all in millimetres except the link count. For example 575 × 93 × 58 means a 575 mm wide belt, 93 mm pitch between drive lugs and 58 lugs around the loop.

Can I fit a track just by matching the width?

No. Width alone does not guarantee fit. Pitch, guide type and link count must all match, and the sprocket teeth should be in good condition, or the belt will ratchet, run off-centre or not fit the tensioner.

How long does a harvester rubber track last?

There is no fixed number of hours: life depends on terrain, driving and maintenance. The reliable approach is to inspect the tread and lugs regularly and replace when cords are exposed, lugs are missing or the belt can no longer be tensioned.

Should the sprocket and rollers be replaced with the track?

Yes, when they are worn. Pointed sprocket teeth or rollers with flat spots will destroy a new belt quickly. Treat the track, sprocket, idlers and seals as one undercarriage system.

Looking for a replacement harvester track or undercarriage parts? Send the stamped size code (or the machine model with a photo of the old track) and your part-number list, and we will confirm the fit and return one consolidated quote with shipping to your port.

Leave a Comment

Your email address will not be published. Required fields are marked *