Right Rock Assy (ZKB40-206a-401-2-00S) for the FM WORLD 6.0P
The right rocker assembly is the pivoting arm on the release side of the steering clutch in the ZKB85 gearbox. It measures 70 x 65 x 50 mm and weighs 0.25 kg, and it is the right-hand half of a matched pair: the left-hand part carries the …-401-1-00S number.
Specifications
| Part Number | ZKB40-206a-401-2-00S |
|---|---|
| Part Type | Right rocker assembly, steering clutch release |
| Dimensions | 70 x 65 x 50 mm |
| Weight | 0.25 kg |
| Hand | Right |
| Fits | FM WORLD 4LZ-6.0P (Ruilong) |
| Availability | In stock, ready to ship |
What this part does
This arm converts a straight pull into the swing that lifts the release mechanism off the steering clutch. Because it pivots rather than slides, all of its wear happens at two places: the pivot bore, which opens up and lets the arm tilt instead of swing true, and the pad where it contacts the release part, which wears into a step. Either one shortens the travel the clutch sees, and a steering clutch that is not fully released drags, heats, and steers sluggishly on one side only.
The right arm and the left arm of the same pair
The two arms are mirror parts, not interchangeable ones. They differ in the …-401-2- and …-401-1- suffix and in which side of the release fork they sit. Fitting the wrong hand puts the contact pad on the wrong face: the arm still moves, so the mistake is not obvious until the machine pulls to one side. Read the suffix before ordering and compare the old arm with the new one pad to pad.
Fitting notes
Work on a clean bench and keep the pivot pin with its own arm, because a pair that has worn together will not swap cleanly. Check the bore for ovality and the pad for a step before the new arm goes in, and confirm the arm swings freely through its full travel without touching the housing. Release travel, free play and the adjustment that follows are set out in the service manual for this gearbox; we do not publish figures for them.
Before you fit it
Look at the pivot pin and the bore together. A worn pin in a new arm still tilts, and a new pin in a worn bore still rattles, so replace whichever half has lost its fit.
Signs it needs replacing
- Steering that engages late or drags on one side
- Clutch pack that runs hot after a few hours of steering
- Pivot bore oval, or a visible step on the contact pad
- Arm that can be rocked by hand before the linkage is loaded
Compatibility and cross reference
Models covered
This arm belongs to the right-hand side of the release linkage on the ZKB85 box fitted to the FM WORLD 4LZ-6.0P. The left-hand arm of the same linkage is a separate part, so order by the …-401-2- suffix rather than by the picture.
Confirming the right part
Confirm ZKB40-206a-401-2-00S on the 70 x 65 x 50 mm envelope and on the right-hand suffix. The left-hand arm of the pair carries a different number and a mirrored pad.
Reading the old part
The stamp sits on the arm body, often under the pad where the linkage hides it. Check the suffix rather than the size alone, since both arms measure the same envelope.
Questions we are asked about this part
How do I tell the right arm from the left?
By the suffix and by the pad. The right-hand part is …-401-2-00S and the left-hand part is …-401-1-00S; on the bench the two sit as mirror images, so lay the old arm beside the new one and compare which face carries the pad.
Can I fit a new arm without touching the rest of the release linkage?
Yes, if the pin, the fork and the release bearing are still sound. A new arm against a worn pad partner simply wears the new pad into the old shape, so inspect the part it pushes before closing the box.




