,

Steering Gear (ZKB80-303-002,012)

Steering gear for the ZKB85 gearbox. Part ZKB80-303-002,012. In-stock replacement for the FM WORLD 4LZ-6.0P (ZKB85) gearbox.

Steering Gear (ZKB80-303-002,012) for the FM WORLD 6.0P

This two-diameter gear sits in the steering section of the ZKB85 gearbox on the FM WORLD 4LZ-6.0P. Its upper end measures 52 mm bore and 68 mm outside; its lower end measures 33 mm bore and 76 mm outside; overall length is 108 mm and weight 1.1 kg.

Specifications

Part NumberZKB80-303-002,012
Part TypeSteering gear (two-diameter)
Upper Bore / Outside52 mm / 68 mm
Lower Bore / Outside33 mm / 76 mm
Length108 mm
Weight1.1 kg
FitsFM WORLD 4LZ-6.0P (Ruilong)
AvailabilityIn stock, ready to ship

What this part does

On a crawler harvester the machine is steered by steering clutches, and this gear is part of the train that drives them. Two diameters on one part means it does two jobs at once: the upper end takes drive and the lower end carries it into the steering clutch side. Because it is common to both tracks, wear here shows as a steering symptom rather than a drive symptom, and it usually appears on one side first as the clutch that receives less clean drive begins to drag.

A steering fault from the gear and one from the clutch

These behave differently. A worn steering gear produces a track that pulls late, hesitates, or will not hold a straight line under load, but the clutch itself still releases. A worn clutch pack produces a track that drags, chatters, or will not disengage at all even when the lever is fully pulled. Both end up as poor steering, so the gear needs to be checked when a clutch rebuild does not fix the complaint.

Fitting notes

Check both bores and both shaft ends before fitting, because a two-diameter part can be good at one end and worn at the other. Assemble so the gear seats fully on both ends rather than being drawn up by a bolt, and confirm the steering clutches release evenly afterwards. Adjustment of the steering linkage and the oil level are per the service manual for this model.

Before you fit it

Measure both bores with a gauge, not by eye. A 52 mm upper and 33 mm lower can look identical to a worn pair until they are measured.

Signs it needs replacing

  • One track steers late or will not hold a straight line under load
  • Steering that improves after a clutch rebuild and then returns
  • Either bore opened up so the gear rocks on its shaft
  • Worn or stepped teeth on the lower diameter

Compatibility and cross reference

Models covered

Steering section of the ZKB85 gearbox on the FM WORLD 4LZ-6.0P (Ruilong). Match ZKB80-303-002,012 as a pair number, since both diameters belong to one part.

Confirming the right part

Confirm ZKB80-303-002,012 on both diameters: 68 mm over a 52 mm bore at the top, 76 mm over a 33 mm bore at the bottom, 108 mm overall.

Reading the old part

The stamp sits high on the upper diameter, exactly where the shaft usually hides it. Measure 52 / 68 mm at the top and 33 / 76 mm at the bottom instead of relying on the stamp.

Questions we are asked about this part

Which end wears first on this gear?

The lower end usually, because it carries drive into the clutch side and takes the steering load. That is why the lower 33 / 76 mm figures are worth measuring even when the upper end looks sound.

Can this gear cause one-sided steering?

Yes. Because it drives the steering clutches, wear on one side can show as one track responding differently from the other, even though the part itself is common to both.

Related parts