,

Driving Gear (ZKB80-305a-004)

39-tooth driving gear for the ZKB85 gearbox. Part ZKB80-305a-004. In-stock replacement for the FM WORLD 4LZ-6.0P (ZKB85) gearbox.

Driving Gear 39T (ZKB80-305a-004) for the FM WORLD 6.0P

This is the large 39-tooth gear in the ZKB85 box on the FM WORLD 4LZ-6.0P: 180 mm outside diameter, 47 mm bore, 45 mm wide, and 3.5 kg. It is the biggest single gear in the gearbox group and the one that takes the input torque first.

Specifications

Part NumberZKB80-305a-004
Part TypeDriving gear, 39 teeth
Bore47 mm
Outside Diameter180 mm
Height45 mm
Teeth39
Weight3.5 kg
FitsFM WORLD 4LZ-6.0P (Ruilong)
AvailabilityIn stock, ready to ship

What this part does

As the largest gear in the box, this one converts the input speed into the working range the rest of the train uses. At 180 mm across and 39 teeth, it has the longest mesh contact of any gear here, which is why it is also the quietest when healthy and the most expensive to ignore. Wear on this gear is not local: once the flanks lose their profile, every gear downstream runs against a slightly wrong input.

This gear and the small gears it drives

The 39-tooth gear is the input side of the train, and the 19- and 23-tooth gears are the driven side. They fail at different rates: the big gear usually shows flank pitting and noise first because it carries the full torque, while the small gears show tooth breakage first because each tooth takes more cycles. Inspecting only the small gears when the box is noisy misses the usual source.

Fitting notes

Support the gear properly when it comes off the shaft, because 3.5 kg on a thin-walled bore is easy to crack by dropping. Check the shaft for fretting and the keyway or spline for step wear before the new gear goes on, and confirm the gear sits square rather than being forced. Axial position, backlash and the oil to refill with are set by the service manual for the ZKB85 box.

Before you fit it

Inspect the shaft surface and the keyway before fitting. A burr or a worn keyway will hold the new gear off-centre and it will run noisy from the first hour.

Signs it needs replacing

  • Constant whine or rumble from the gearbox that changes with load
  • Pitting or spalling on the tooth flanks near the pitch line
  • Broken or chipped teeth, usually on the loaded side
  • Metal debris in the drained oil or on the magnetic plug

Compatibility and cross reference

Models covered

The input-side gear of the ZKB85 gearbox on the FM WORLD 4LZ-6.0P (Ruilong). Compare ZKB80-305a-004 with the number on the gear you are replacing.

Confirming the right part

Confirm ZKB80-305a-004 on 39 teeth and 180 mm outside. This is the only 39-tooth gear in the ZKB85 group, so the tooth count alone narrows it down.

Reading the old part

With 39 teeth this is the one gear in the box you can identify on sight. The number is stamped on the web; measure 180 mm across and 47 mm at the bore to confirm.

Questions we are asked about this part

Is a noisy gearbox always this gear?

Not always, but it is the first place to look on this box because it carries the full input torque. Confirm by checking the flanks for pitting before ordering, since bearings can produce a similar rumble.

Can the 39-tooth gear be refitted after inspection?

If the flanks are unmarked and the bore is still round, yes. Once pitting reaches the pitch line or the bore has opened up, refitting it only moves the noise to the next season.

Related parts