,

Half Shaft Right Arm ZKB65a-W3.5H-205-600B1G1

Right-hand half shaft with steering arm. Part ZKB65a-W3.5H-205-600B1G1. In-stock replacement for the FM WORLD 4LZ-6.0P (ZKB85) gearbox.

Half Shaft Right Arm (ZKB65a-W3.5H-205-600B1G1) FM WORLD 6.0P

The right-hand half shaft carries the steering arm at one end and runs in the final drive at the other. It is 60 mm at the shaft, 157 mm across the arm, 470 mm long, and weighs 7.6 kg. The left-hand part is 448 mm long, so the two arms of the pair differ by 22 mm.

Specifications

Part NumberZKB65a-W3.5H-205-600B1G1
Part TypeHalf shaft with steering arm, right
Shaft Diameter60 mm
Arm Width157 mm
Length470 mm
Weight7.6 kg
FitsFM WORLD 4LZ-6.0P (Ruilong)
AvailabilityIn stock, ready to ship

What this part does

This is a loaded, rotating part with two different duties. Along its length it transmits drive to the final drive, so the spline or key at the inner end carries torque. At the outer end the arm takes the steering load, which is a bending load rather than a twisting one. That is why failures show at the two ends first: spline wear at the drive end, and a crack or a worn eye at the arm end, while the middle of the shaft stays sound.

Right arm and left arm: 470 mm against 448 mm

The pair is mirror-finished but not the same length. Right is 470 mm, left is 448 mm, a difference of 22 mm that is easy to lose when both are laid on the same pallet. Fitting the longer part on the left side pushes the arm outward, loads the steering linkage off-centre, and the machine pulls to one side. Measure before fitting and keep the old parts tagged by side.

Fitting notes

Support the shaft by its body, not by the arm eye, when it is lifted; 7.6 kg on a lever of 157 mm will bend what it is dropped onto. Clean the spline and check it for step wear, check the arm eye for ovality, and confirm the seal surface is unmarked. Bearing preload, end play and the steering adjustment afterwards follow the service manual.

Before you fit it

Check the spline and the arm eye together. A worn spline lets the shaft rock under load, and a worn eye lets the steering arm move before the shaft does; either one feels like steering play.

Signs it needs replacing

  • Steering play that grows through the season
  • Spline fretting, step wear or polish at the drive end
  • Oval or cracked eye at the arm end
  • Oil seeping at the seal surface under the arm

Compatibility and cross reference

Models covered

Right-hand half shaft of the final drive and steering linkage on the FM WORLD 4LZ-6.0P. It pairs with the 448 mm left-hand shaft, and the two are handed, so order by length as well as by number.

Confirming the right part

Confirm ZKB65a-W3.5H-205-600B1G1 on 470 mm length, 60 mm shaft and 157 mm arm. The left-hand part is 448 mm and carries a different number.

Reading the old part

The number is stamped on the arm body, often faint after years of mud. Measure 470 mm end to end; a right arm that reads 448 mm is the left-hand part.

Questions we are asked about this part

Can the right and left arms be swapped?

No. Right is 470 mm and left is 448 mm, and the arms are handed. A swap puts the steering geometry out by 22 mm and the machine will not steer evenly.

The arm eye is worn. Can it be bushed?

A bushing can restore the eye if the casting is still sound, but it changes the geometry and the fit of the pin. On a part that also carries drive torque, replacement is the safer route.

Related parts