,

Left Shaft ZKB65-W3.5H-305-001

Splined left shaft with different teeth at each end. Part ZKB65-W3.5H-305-001. In-stock replacement for the FM WORLD 4LZ-6.0P (ZKB85) gearbox.

Left Shaft (ZKB65-W3.5H-305-001) for the FM WORLD 6.0P

This left shaft is 625 mm long and weighs 9.4 kg, with two different splined ends: the left end has 18 teeth on a 30 mm / 50 mm diameter pair, the right end has 20 teeth on a 53 mm diameter. Because the two ends differ, the shaft can only go in one way round.

Specifications

Part NumberZKB65-W3.5H-305-001
Part TypeLeft shaft, splined both ends
Left End18 teeth, 30 / 50 mm
Right End20 teeth, 53 mm
Length625 mm
Weight9.4 kg
FitsFM WORLD 4LZ-6.0P (Ruilong)
AvailabilityIn stock, ready to ship

What this part does

An 18-tooth end and a 20-tooth end on the same shaft is a deliberate design choice: it prevents the shaft from being fitted the wrong way round. Each spline mates with a different hub, so the 18-tooth side carries one duty and the 20-tooth side another. Wear therefore appears on one end first, usually the one that sees more reversing or more load, and the shaft starts to rattle at that coupling while the rest of it stays quiet.

Reading a two-ended shaft before it goes in

Count both ends before fitting: 18 teeth into the 18-tooth hub and 20 teeth into the 20-tooth hub. A shaft offered up the wrong way will not enter far enough, and forcing it damages both splines. If it enters easily but rattles, the spline fit has opened up rather than the shaft being backwards, which is the more expensive failure of the two.

Fitting notes

Clean both splines and check each for step wear and fretting, then confirm the shaft turns true in its bearing positions. Fit it with the 18-tooth end to the 18-tooth hub and do not drive it in with a hammer, because 9.4 kg on a spline will peen the teeth. End play, bearing preload and the coupling arrangement follow the service manual.

Before you fit it

Count the teeth at both ends and match them to the hubs before the shaft goes in. Once the wrong end has been forced, the spline is damaged even after it is removed.

Signs it needs replacing

  • Rattle or knock at one coupling, silent at the other
  • Spline fretting, polish or step on the loaded end
  • Shaft that will not turn true in its bearings
  • Metal particles in the oil with no gear damage found

Compatibility and cross reference

Models covered

Splined left shaft in the 305 group of the ZKB85 box on the FM WORLD 4LZ-6.0P. Its 18-tooth and 20-tooth ends belong to two different hubs, so both counts matter when ordering.

Confirming the right part

Confirm ZKB65-W3.5H-305-001 on 625 mm length, 18 teeth at the 30 / 50 mm end and 20 teeth at the 53 mm end. A shaft with equal splines at both ends is a different part.

Reading the old part

The number is stamped near one end on the shaft body. Count teeth at both ends and measure 625 mm, since the tooth counts are the fastest way to tell this shaft from its neighbours.

Questions we are asked about this part

Can the shaft be fitted either way round?

No. One end has 18 teeth on a 30 / 50 mm diameter and the other has 20 teeth on 53 mm, so only one orientation enters its hubs properly. Forcing it damages both splines.

How do I know which end is worn?

Look at both splines. The loaded end shows fretting and a step first, while the other end often looks new; the rattle at that coupling is the symptom to match with what you see.

Related parts