Combine Harvester Parts Names & Diagram: A Complete Visual Guide

A self-propelled combine turns three separate jobs — reaping, threshing and winnowing — into one pass, which is why it carries hundreds of parts spread across nine working systems. Mechanics and parts buyers waste time (and money) simply because a single part is called different names in the manual, at the counter and on the packing slip. This guide names every main part in correct English, shows where it sits on a tracked rice combine, and points you to the parts that actually wear out.

The diagrams below use a tracked rice combine (the layout used across South and Southeast Asia). Large Western wheat combines differ in size and use straw walkers instead of an axial rotor, but the part names and the crop path are the same.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Schematic, not to scale. Part positions vary by model. Whole-feed and head-feed rice combines differ mainly in the feeding and threshing sections, covered in detail later.

Main parts at a glance (numbered legend)

No.Part nameSystemWhat it does
1Reel (bats & tines)Header / cuttingLays the standing crop back over the knife
2Cutterbar (knife sections, guards)Header / cuttingCuts the stems near the ground
3Header auger (cross auger)Header / cuttingGathers the cut crop to the centre of the header
4Feeder house / chain conveyorFeedingCarries the crop up into the threshing unit
5Cab / operator stationControlControls and monitors the machine
6Engine (diesel)PowerSupplies power to the drives and wheels
7Grain tank (hopper)Grain handlingTemporarily stores clean grain
8Unloading augerGrain handlingTransfers grain out into a trailer
9Threshing drum / rotorThreshingKnocks the grain out of the head
10Concave (grate)ThreshingFixed surface against which the grain is rubbed free
11Straw walker / separatorSeparationRecovers grain still trapped in the straw
12Cleaning fan / blowerCleaningBlows out light chaff and dust
13Upper sieve (chaffer)CleaningFirst separation of grain from residue
14Lower sieve (cleaning shoe)Final cleaningFinal cleaning before the grain is lifted
15Grain elevatorGrain handlingLifts clean grain up to the grain tank
16Clean grain augerGrain handlingCollects grain under the sieves and feeds the elevator
17Tailings return (rethresher)CleaningReturns unthreshed heads for a second pass
18Straw chopperResidueChops the straw before discharge
19Spreader / discharge hoodResidueSpreads or windrows the residue
20Rubber trackChassis / mobilityLow ground pressure for wet paddy fields
21Drive sprocket, rollers & idlerChassis / mobilityDrive and guide the track

Follow the crop: the seven stages

You never have to memorise the parts in isolation. Follow the crop through the machine and the layout becomes logical. Every system in the table above appears once in this chain:

1. Cut & gather→2. Feed→3. Thresh→4. Separate→5. Clean / winnow→6. Elevate & store→7. Unload

Clean grain follows one path (down through the sieves, up the elevator, into the tank). Straw and chaff follow another path (back and out the rear). A third stream — the tailings — loops back to be threshed again. When the machine leaves grain in the field, it is failing at one of these stages, and the part names tell you exactly where to look.

1. Header and cutting parts

The header is the first working part and sets the pace for everything behind it. Its four parts work in a fixed sequence, and the detail is laid out in the combine header system guide.

  • Reel (1). A rotating wheel with horizontal bats and spring tines (teeth). It turns slightly faster than ground speed and lays the standing or lodged crop back onto the knife. Tines that are bent or missing leave uncut strips. Bolt-on reel spring tines are replaced one at a time.
  • Cutterbar (2). A reciprocating knife driven by a wobble box (or an epicyclic drive). It is built from knife sections (the sharp, serrated blades), knife guards (the fingers that hold the stems), and hold-down clips. Blunt knife sections or chipped guards tear rather than cut and cause plugging. Replace cutting blade assemblies and knife guards as matched sets.
  • Header auger (3). The large cross auger with helical flighting and retractable fingers sweeps the cut material to the centre. Auger sliders set the small floating gap above the header floor. Worn flighting, broken fingers or thin auger sliders create the uneven feed that shows up later as threshing loss. Complete header auger welds are available when the barrel itself is worn.
  • Row dividers / crop lifters on the front edges separate and lift lodged rows so they meet the knife cleanly.

All these belong to the header and conveyor parts category.

2. Feeding parts

The feeder house (4) is the sloped throat between the header and the threshing unit. On whole-feed combines it is a chain-and-slat conveyor — a chain with steel slats that drags the entire cut plant up an incline. A slack or worn chain lets the crop tumble back instead of feeding evenly, and the classic symptom is “slugging” at the drum. Tension the chain and replace it as a set when it stretches; complete feeder chain assemblies and feeder drums are the service items.

Head-feed difference: a Japanese-style head-feed combine does not feed the whole plant. A holding (culm) chain grips the base of the stems and feeds only the panicles into the cylinder, leaving the straw intact. This is the main structural difference between the two machine types and is explained below.

3. Threshing parts

Threshing is the heart of the machine: it releases the grain without cracking it. The full threshing and cleaning system guide covers adjustments, but the parts are:

  • Threshing drum or rotor (9). On conventional (whole-feed) machines a transverse cylinder carries steel rasp bars — fluted, ridged bars that strike and rub the grain. On axial-flow machines a longitudinal rotor performs threshing and separation over a longer path. Head-feed machines use a long axial cylinder fitted with wire (弓齿 / inverted-U) teeth. The rasp bar teeth bars are high-wear items: once the leading edges round off, the operator must tighten the gap to keep threshing, which raises cracked grain.
  • Concave (10). A fixed, curved grate beneath the cylinder. Crop passes through the gap between drum and concave, and the free grain drops through the grate. Concave clearance is the single most important setting: too tight cracks grain and wastes power; too loose leaves grain in the head. Replacement grates include the Kubota concave, Lovol concave grate, and front / rear concave screens.

All threshing drum, concave, bar and tooth parts live under the threshing parts category.

4. Separation parts

After threshing, free grain is mixed with straw and chaff. Separation recovers the grain that is still trapped in the straw mat before it leaves the machine.

  • Straw walkers (11) on conventional combines: a set of oscillating, keyed platforms that toss the straw upward and rearward so that trapped grain falls through the grate.
  • Rotary separator / separation grates on axial-flow combines: the rear of the rotor flings grain outward through grates by centrifugal force.
  • Rear beater / rethresher pulls the straw off the cylinder and can re-thresh unthreshed heads.

5. Cleaning (winnowing) parts

The material that falls through the grates lands on the cleaning shoe — the assembly of two oscillating sieves and a fan. It separates clean grain from chaff by particle size and by weight.

  • Cleaning fan / blower (12). Drives a controlled airstream up through the sieves to lift off light chaff and dust. Low fan speed leaves a dirty sample; too much wind blows good grain out the back. Service items include fan blades, the fan shaft and fan bearings.
  • Upper sieve / chaffer (13). The larger, louvred top sieve; grain falls through, larger trash rides out. Replaceable units include upper sieve assemblies.
  • Lower sieve / cleaning shoe (14). The finer bottom sieve that finishes the clean grain. Components include the Kubota sieve, sieve assemblies, and vibrating screen assemblies.
  • Tailings return (17). An auger/elevator that collects partly-threshed material from the lower sieve and returns it to the threshing unit. A steady high tailings volume is a setting warning, not a fault in the return itself.

All sieves, screens and fan parts are in the cleaning sieves category.

6. Grain handling: augers, elevator, tank and unloading

Once clean, the grain is collected, lifted, stored and discharged.

  • Clean grain auger (16) runs beneath the sieves and moves grain to the elevator foot. Worn flighting leaves grain in the shoe.
  • Grain elevator (15) is a chain-and-paddle (or enclosed) vertical conveyor that lifts clean grain into the tank. Worn paddles and a slack chain reduce capacity and damage grain. Elevator augers are a routine replacement.
  • Grain tank / hopper (7) stores clean grain; rice combines often carry a 300–1,500 kg tank with level sensors.
  • Unloading auger (8) swings from the tank to fill a trailer. It is a long tube with internal flighting and a pivot base. Items include unloading auger tubes, vertical auger tubes and the unloading hydraulic cylinder.

These are grouped under the grain tank and unloading category.

7. Residue management

  • Straw chopper (18) — a high-speed rotor with knives that shreds the straw for no-till spreading.
  • Spreader / discharge hood (19) either throws the residue evenly across the cutting width or lays it in a windrow for baling. The chopper is disengaged or bypassed when the straw is baled.

8. Power and transmission parts

A diesel engine drives the header, the processing drums and the ground drive through belts, chains, shafts and gearboxes.

  • Engine (6). Usually a 4-cylinder vertical diesel (e.g. Kubota V2403, Yanmar 4TNV98, or the Changchai 4G33 / 4L88 fitted to Chinese combines). Fast-moving service items are filters: oil filters, diesel filters, fuel filter assemblies and the HST oil filter. Internal wear parts include cylinder liners and piston ring kits. See the engine parts category.
  • Belts and chains transmit drive to the header, augers, drum, fan and screens. V-belts (e.g. the drum belt), conveyor chains and sprockets are wear items.
  • Gearboxes reduce speed and increase torque for each working unit — examples are gearbox assemblies for the rethresher and auger drives.
  • HST (hydrostatic transmission). The hydraulic pump-and-motor unit gives stepless ground speed, which is why a tracked rice combine moves without a gear clutch. Seals, swash plates and the HST assembly itself are specialised parts; a hydraulic gear pump also raises the header and operates the unloading auger. See HST and hydraulic drive and gearbox parts.

9. Chassis, tracks, cab and electrical

Fasteners, bearings and other consumables are grouped under standard parts.

Whole-feed vs head-feed rice combines — and why the parts differ

There are two families of rice combine, and ordering the right parts depends on knowing which one you run. Manufacturers label them Conventional (whole-feed) and Head-feeding (also called hold-on or half-feed) — the terms used by Yanmar’s own model sheets.

Whole-feed / conventionalHead-feed (half-feed)
What enters the cylinderThe whole cut plant — panicle and strawOnly the panicles; a holding chain grips the straw
Threshing elementRasp-bar drum or axial rotorLong axial cylinder with wire (弓齿) teeth
Typical examplesFM World 4LZ-6.0P / 4.0E, Lovol RG series, Zoomlion ZL105, Yanmar AW70/AW82Kubota DC70 and DC68G
ThroughputHigher, suited to larger plotsLower, but gentler on grain and straw
Distinctive partsChain-and-slat feeder house, rasp bars, large concaves, straw walkers or rotorHolding/culm chain, wire-tooth cylinder, feeding-drum set

Throughput, straw condition and field size decide the machine, but the part numbers never interchange between families — always confirm the model before ordering.

Which parts wear out fastest (what to keep on the shelf)

The abrasive crop and dust mean a short list of parts causes most of the downtime. These are the items growers and contractors keep in stock rather than waiting on shipping; the full maintenance logic is in the combine wear parts replacement guide.

  • Knife sections and knife guards, hold-down clips (header).
  • Reel spring tines and reel bearings.
  • Feeder chain and feeder slats, header auger sliders.
  • Rasp bars / wire teeth and concave grates (the heart of threshing quality).
  • Sieve screens and fan blades.
  • V-belts and drive chains, sprockets, sealed bearings.
  • Rubber tracks, track rollers and idlers.
  • Engine oil, diesel and hydraulic filters, with a set of hydraulic seals.

How to order the correct part by name and number

The same part can carry three different names in different catalogues, so identify it on more than one criterion. The spare-parts ordering checklist walks through the full method, but the essentials are:

  1. Exact machine model and year. “Kubota” or “Lovol” is not enough — use the model plate (e.g. DC70, AW82, 4LZ-6.0P, RG, ZL105) and engine type.
  2. The part number (P/N) from the parts book — this is the fastest identifier. Note the figure number and key number too.
  3. Part name using the system on this page (e.g. “upper sieve (chaffer)”, not “the sieve bit”).
  4. A clear photo of the broken part and any stamped number, plus quantity.
  5. Dimensions for bearings, belts and seals (bore × outside × width, or belt code).

Find the part by name — or download the parts book

Search by machine and part name across the full catalogue, or download the illustrated parts book (PDF) for your combine and quote by part number. Free parts lookup by photo is available before ordering.

Fastest on WhatsApp: message us with the model, part name and a photo.

Recommended next reading: the header system guide, the threshing and cleaning guide, the wear parts replacement guide, and the bearing size chart.

Leave a Comment

Your email address will not be published. Required fields are marked *